How to stick the tiles in the kitchen
It is time the long-awaited repairs in the kitchen, which can be made with their own hands, without the help of professionals. The process of sticking tiles do not require special skills. - Your task is to follow the clear recommendations and excellent results will be forthcoming. It is not necessary to put the tiles on the wall in the kitchen, you can make a kind of "apron".
You will need
- Metal profiles;
- Tin snips;
- Tile and Bulgarian;
- Adhesive mixture;
- primer;
- level;
- Spatulas;
- Grout;
- tile;
- Dowels;
- Crosses for joints;
- Building area.
Instructions
1.Podgotovte all the necessary tools and start the preparation of the walls. Repel old tiles and clean off the spatula old adhesive coating to the base of the wall. If the walls had wallpaper or putty, remove it completely and wash the walls of whitewash. Use a level to check the evenness of the wall vertically and horizontally. In the case of large deviations have plastered walls.
2. On the walls are made of purified notches with a hammer or chisel. Then walk or acrylic latex primer. Leave to dry wall on one or two hours. If you decide to glue tiles on the in situ concrete, whereas the surface should be pre-coated "Betonokontaktom" (drying time varies from twelve to eighteen hours).
3. In the future, depending on the height of the furniture that you will install, specify the lower level tile. Measure from the bottom of about 85-95 centimeters and mark. Using a long level draw a horizontal line across the length of the planned installation of the tiles.
4.Vozmite metal profile, measure the desired length, cut with scissors, metal and attach it to the wall in the level. This profile will help you to maintain a perfect strictly horizontal level, which is an important factor in laying the apron.
5.Razvedite small amount of adhesive with water according to the specified instructions and mix thoroughly. Begin to lay the tiles from the bottom up, from the visible angle. Apply the adhesive with a notched trowel to the point where further be laid tiles. Narrow trowel, apply a thin layer of glue on the back of the tile and set it in place. Flick push her face down into the solution and a rubber mallet.
6.Vystavite strictly tiles horizontally and vertically with a short level. If it is not level, remove it with a spatula, or enclose the adhesive as needed. First install the tiles perfectly and flawlessly, as they will depend on the outcome of your work. Pay attention at the picture, the back of the tile has a pointer arrow.
7.Zatem side put a second tile and check the level in the same way. Install crosses between neighboring ribs. Use your fingers to make sure the seam, the transition should not be felt. In the first place the third tile, check the angle between the horizontal and the vertical face of a square. Likewise Lay the remaining tiles, do not forget to use the crosses.
8. In the process of laying tile, you will need to trim it to size. This can be done using the lever Tile or grinders. At the end styling apron remove all the crosses and clean the joints between the tiles, replace the crosses that the seams will not warp in the process of drying.
9.Spustya day after laying tile, you can safely proceed to the grout. Dissolve the dry mixture with water until thick sour cream (use a mixture in small portions, as it is efficient for twenty minutes). Moisten the joints and apply grout with a rubber spatula pressed movements. Surplus remove toward the seam, after twenty minutes, wipe with a slightly damp cloth.
note
How to stick tile. The method of applying any adhesive the same. For this type of work is best suited with a notched trowel. In choosing the adhesive for a particular tile you tell Sales. Let's get down to the application of adhesive on the part of the wall where we will glue tiles. Cover the wall with glue is needed. Notched trowel "take away" the tile adhesive on the surface of the wall. Thus the adhesive layer should have a thickness of approximately 2.5 mm.
Helpful advice
Before you glue the tiles on the wall you need to do preparatory work, remove old paint, make the incision, if necessary, to align the wall primed. Gluing the tiles to the wall are two ways, from the center of the wall, in which case the angles of the tiles will be at the same distance and angle from the distal, then trimming the tiles will be minimal. Dilute tile adhesive, and using a special notched trowel, apply it first to the wall, 1 to 2 square meters, and then on the tiles.
It is time the long-awaited repairs in the kitchen, which can be made with their own hands, without the help of professionals. The process of sticking tiles do not require special skills. - Your task is to follow the clear recommendations and excellent results will be forthcoming. It is not necessary to put the tiles on the wall in the kitchen, you can make a kind of "apron".
You will need
- Metal profiles;
- Tin snips;
- Tile and Bulgarian;
- Adhesive mixture;
- primer;
- level;
- Spatulas;
- Grout;
- tile;
- Dowels;
- Crosses for joints;
- Building area.
Instructions
1.Podgotovte all the necessary tools and start the preparation of the walls. Repel old tiles and clean off the spatula old adhesive coating to the base of the wall. If the walls had wallpaper or putty, remove it completely and wash the walls of whitewash. Use a level to check the evenness of the wall vertically and horizontally. In the case of large deviations have plastered walls.
2. On the walls are made of purified notches with a hammer or chisel. Then walk or acrylic latex primer. Leave to dry wall on one or two hours. If you decide to glue tiles on the in situ concrete, whereas the surface should be pre-coated "Betonokontaktom" (drying time varies from twelve to eighteen hours).
3. In the future, depending on the height of the furniture that you will install, specify the lower level tile. Measure from the bottom of about 85-95 centimeters and mark. Using a long level draw a horizontal line across the length of the planned installation of the tiles.
4.Vozmite metal profile, measure the desired length, cut with scissors, metal and attach it to the wall in the level. This profile will help you to maintain a perfect strictly horizontal level, which is an important factor in laying the apron.
5.Razvedite small amount of adhesive with water according to the specified instructions and mix thoroughly. Begin to lay the tiles from the bottom up, from the visible angle. Apply the adhesive with a notched trowel to the point where further be laid tiles. Narrow trowel, apply a thin layer of glue on the back of the tile and set it in place. Flick push her face down into the solution and a rubber mallet.
6.Vystavite strictly tiles horizontally and vertically with a short level. If it is not level, remove it with a spatula, or enclose the adhesive as needed. First install the tiles perfectly and flawlessly, as they will depend on the outcome of your work. Pay attention at the picture, the back of the tile has a pointer arrow.
7.Zatem side put a second tile and check the level in the same way. Install crosses between neighboring ribs. Use your fingers to make sure the seam, the transition should not be felt. In the first place the third tile, check the angle between the horizontal and the vertical face of a square. Likewise Lay the remaining tiles, do not forget to use the crosses.
8. In the process of laying tile, you will need to trim it to size. This can be done using the lever Tile or grinders. At the end styling apron remove all the crosses and clean the joints between the tiles, replace the crosses that the seams will not warp in the process of drying.
9.Spustya day after laying tile, you can safely proceed to the grout. Dissolve the dry mixture with water until thick sour cream (use a mixture in small portions, as it is efficient for twenty minutes). Moisten the joints and apply grout with a rubber spatula pressed movements. Surplus remove toward the seam, after twenty minutes, wipe with a slightly damp cloth.
note
How to stick tile. The method of applying any adhesive the same. For this type of work is best suited with a notched trowel. In choosing the adhesive for a particular tile you tell Sales. Let's get down to the application of adhesive on the part of the wall where we will glue tiles. Cover the wall with glue is needed. Notched trowel "take away" the tile adhesive on the surface of the wall. Thus the adhesive layer should have a thickness of approximately 2.5 mm.
Helpful advice
Before you glue the tiles on the wall you need to do preparatory work, remove old paint, make the incision, if necessary, to align the wall primed. Gluing the tiles to the wall are two ways, from the center of the wall, in which case the angles of the tiles will be at the same distance and angle from the distal, then trimming the tiles will be minimal. Dilute tile adhesive, and using a special notched trowel, apply it first to the wall, 1 to 2 square meters, and then on the tiles.
Комментариев нет:
Отправить комментарий